www.vbs-hobby.com 
Exclusive offersGarden sign "Bienen bei der Arbeit“/ Bees at work"
Instructions No. 2073 Instructions No. 2073 Difficulty: Advanced Working time: 1 hour 30 Minutes
The topic bees is more topical than ever, because the insects have it more and more difficult and need our support. Of course, this is also a small issue and so you can already do a lot in your home garden or on the balcony to help the busy pollinators
If you perhaps have a corner that is only for the bees or even a beehive with you, it can't hurt to point it out. This way, careless visitors are protected and you also have a nice eye-catcher.
If you perhaps have a corner that is only for the bees or even a beehive with you, it can't hurt to point it out. This way, careless visitors are protected and you also have a nice eye-catcher.
1. Paint and label the sign
For priming, take your paint, put a few good spots of it on the shield and spread it all over with a sponge or brush. Let this first layer dry almost completely. You can use a hair dryer to speed up the process
Then use the brush to add more accents, but with less paint, so that the colours blend more into each other without mixing. Then you blow-dry again. You do this until you are satisfied with your shield
Then let everything dry out well and draw the writing and honeycombs for yourself. Either do this freehand or use templates or the like to help you.
For priming, take your paint, put a few good spots of it on the shield and spread it all over with a sponge or brush. Let this first layer dry almost completely. You can use a hair dryer to speed up the process
Then use the brush to add more accents, but with less paint, so that the colours blend more into each other without mixing. Then you blow-dry again. You do this until you are satisfied with your shield
Then let everything dry out well and draw the writing and honeycombs for yourself. Either do this freehand or use templates or the like to help you.
Then rework the contours of the honeycombs with brown paint and maybe lighten the interior a little bit, so that the individual honeycombs come out better
Let it dry and then fill in the writing. You can either use or Black take Brown - depending on how strong your contrast should be
Then let everything dry well again.
Let it dry and then fill in the writing. You can either use or Black take Brown - depending on how strong your contrast should be
Then let everything dry well again.
2. Tinker beehives
For the bees, you first prepare the hemispheres. If you have all three hemisphere sizes at hand you can make three different bees (see picture above left)
Everything that later becomes the head, you paint with the brown color. All other hemispheres you paint yellow
When the yellow paint is dry, you can paint the stripes. So that not every bee is the same, you can vary the thickness and number of stripes.
For the bees, you first prepare the hemispheres. If you have all three hemisphere sizes at hand you can make three different bees (see picture above left)
Everything that later becomes the head, you paint with the brown color. All other hemispheres you paint yellow
When the yellow paint is dry, you can paint the stripes. So that not every bee is the same, you can vary the thickness and number of stripes.
3. Finish the sign
If the hemispheres are dried, you stick the bees at different places on the sign with the Handicraft glue . Between two hemispheres you should always leave a small gap for the wire or the wings
If the glue is not yet on, you can still move them while "winging"
From the wire you cut pieces, which you then bend to the wings and fix them with hot glue between the hemispheres on the shield. You can also vary the shape and size of the wings, just like the bodies. You can also mount the wings flat or slightly protruding
With smaller pieces of aluminium wire from you form the feelers, of which you bend the end only slightly and fix them with hot glue
If you don't want to work with wire, you can also paint on the wings and feelers. Or you can combine both variants
If the hemispheres are dried, you stick the bees at different places on the sign with the Handicraft glue . Between two hemispheres you should always leave a small gap for the wire or the wings
If the glue is not yet on, you can still move them while "winging"
From the wire you cut pieces, which you then bend to the wings and fix them with hot glue between the hemispheres on the shield. You can also vary the shape and size of the wings, just like the bodies. You can also mount the wings flat or slightly protruding
With smaller pieces of aluminium wire from you form the feelers, of which you bend the end only slightly and fix them with hot glue
If you don't want to work with wire, you can also paint on the wings and feelers. Or you can combine both variants
Now you only still need to hang up your sign in the garden and maybe watch the bees at work
Have fun doing it!
Have fun doing it!
